Raj KAJ (scottobear) wrote,
Raj KAJ
scottobear

Raspberry Pi Projects:

wpid-screenshot_2014-07-08-18-37-58_kindlephoto-134975773.png

  1. Set up a tiny (3.5″) display on one of the Raspberry Pis -
  2. then slap Kali Linux on that device.
  3. House Temperature / Humidity Sensor Monitor and  Kitty Cam
  4. Media CenterWill it Do Netflix? 

Possible others:

Since I’ve recently received for Fur-baby father’s day last Saturday at Micro Center -

MCM Electronics Raspberry Pi 2 Model B Camera Kit  -

Raspberry Pi 2 Model B Board, 8GB Operating System microSD Card, Multicomp Clear Pi 2 Model B Case, Raspbery Pi Wi-Pi wireless ethernet adapter, Raspberry Pi Power Supply, Pi Camera, 36 Page Raspberry Pi User Guide

MCM Electronics Raspberry Pi 2 Model B Media Center -

Raspberry Pi 2 Model B Board, 8GB Operating System microSD Card, Multicomp Black Pi 2 Model B Case, Raspberry Pi Power Supply, Wi-Pi Wireless Adapter, 3′ HDMi Cable, 7′ Ethernet Cable, 36 Page Raspberry Pi User Guide

MCM Electronics Raspberry Pi 2 Model B Complete Kit

Raspberry Pi 2 Model B Board, 8GB Operating System microSD Card, Multicomp Clear Pi 2 Model B Case, Raspberry Pi Power Supply, Wi-Pi Wireless Adapter, Raspberry PI Drawstring Bag, Raspberry Pi Power Supply, Wi-Pi Wireless Adapter, Cyntech Raspberry Pi Hub, USB Keyboard, USB Mouse, 3′ HDMi Cable, 36 Page Raspberry Pi User Guide

(To make the Keyboard behave properly with the Raspberry Pi, I had to do the following -

  • Switch to root user.
  • Run ‘dpkg-reconfigure locales’ and change from en_GB.UTF-8 to en_US.UTF-8.
  • Run ‘dpkg-reconfigure keyboard-configuration’ and change the keyboard to USA PC104 )

Additionally, I still have my Arduino Starter Kit. (from my Birthday haul this year)

1 x Arduino Projects Book
1 x Arduino UNO Rev 3 microcontroller
1 x USB cable
1 x Breadboard
1 x Easy-to-assemble wooden base
1 x 9V battery snap
70 x Solid core jumper wires
2 x Stranded jumper wires
6 x Photoresistors
3 x Potentiometers (10K ohm)
10 x Push buttons
1 x Temperature sensor
1 x Tilt sensor
1 x Alphanumeric LCD (16×2 character display)
1 x Bright white LED
1 x Multicolor RGB LED
8 x Red LEDs
8 x Green LEDs
8 x Yellow LEDs
3 x Blue LEDs
1 x Small DC motor (6/9V)
1 x Small servo motor
1 x Piezo capsule
1 x H-bridge motor driver
2 x Optocouplers
5 x Transisitors
2 x Mosfet transistors
5 x 100nF capacitors
3 x 100uF capacitors
5 x 100pF capacitors
5 x Diodes
3 x Transparent gels (red, green, blue)
1 x 40 pin male header strip
20 x 220 ohm resistors
5 x 560 ohm resistors
5 x 1K ohm resistors
5 x 4.7K ohm resistors
10 x 10K ohm resistors
5 x 1M ohm resistors
5 x 10M ohm resistors

I’ve also ordered:

PiTFT Plus 480x320 3.5

PiTFT Plus 480×320 3.5″ TFT+Touchscreen for Raspberry Pi – Pi 2 and Model A+ / B+ PID: 2441

Raspberry Pi Model B+ / Pi 2 Case Lid - Clear
Raspberry Pi Model B+ / Pi 2 Case Lid – Clear PID: 2257
Pi Model B+ / Pi 2 Case Base - Clear
Pi Model B+ / Pi 2 Case Base – Clear PID: 2253
Assembled Pi Cobbler Plus - Breakout Cable for Pi B+/A+/Pi 2
Assembled Pi Cobbler Plus – Breakout Cable for Pi B+/A+/Pi 2 PID: 2029
I may investigate a battery pack later, but for now, plugging into the wall looks good. 

Originally published at The Scotto Grotto. You can comment here or there.

Tags: arduino, projects, raspberry pi, uncategorized
Subscribe
  • Post a new comment

    Error

    default userpic

    Your reply will be screened

    Your IP address will be recorded 

    When you submit the form an invisible reCAPTCHA check will be performed.
    You must follow the Privacy Policy and Google Terms of use.
  • 0 comments